View MAX95860710_4127582.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

19-0744; Rev 5; 10/07
KIT ATION EVALU BLE AVAILA
Single, Dual, Triple, and Quad Standard-Definition Video Filter Amplifiers with AC-Coupled Input Buffers
General Description
The MAX9586-MAX9589 are small, low-power, multichannel video amplifiers with integrated reconstruction filters and input clamps. Specially suited for standarddefinition video signals, these devices are ideal for a wide range of television and set-top box applications. The video signals from the outputs of a digital-to-analog converter (DAC) are AC-coupled to the inputs of the MAX9586-MAX9589. External video signals, in which the DC bias is usually not known, can also be AC-coupled to the inputs of the MAX9586-MAX9589. The input sync-tip clamps set the DC level of composite video or luma signals, and the input bias circuits set the DC level of chroma signals. The reconstruction filter typically has 1dB passband flatness at 8.5MHz and 55dB attenuation at 27MHz. The amplifiers have 2V/V gain and the outputs can be DCcoupled to a 75 load, which is the equivalent of two video loads, or AC-coupled to a 150 load. The MAX9586-MAX9589 operate from a 2.7V to 3.6V single supply and are specified over the -40C to +125C automotive temperature range. The MAX9586-MAX9589 are offered in small SOT23 and MAX(R) packages.
Features
o Single- (MAX9586), Dual- (MAX9587), Triple- (MAX9588), and Quad- (MAX9589) Channel Devices o 8.5MHz, 1dB Passband o 55dB Attenuation at 27MHz o Fixed Gain of 2V/V o Low Power: 4.25mA per Channel o 2.7V to 3.6V Single-Supply Operation o Small SOT23 and MAX Packages
MAX9586-MAX9589
Ordering Information
PART MAX9586AZK+T MAX9587AZT+T MAX9588AUA+T MAX9589AUB+T PINPACKAGE 5 Thin SOT23-5 6 Thin SOT23-6 8 MAX-8 10 MAX-10 CHANNELS 1 2 3 4 PKG CODE Z5-1 Z6-1 U8-1 U10-2
Applications
Set-Top Boxes Televisions
MAX is a registered trademark of Maxim Integrated Products, Inc.
Note: All devices are specified over the -40C to +125C operating temperature range. +Denotes a lead-free package. T = Tape and reel.
Pin Configurations and Selector Guide located at end of data sheet.
Block Diagrams
UNKNOWN BIAS INA CLAMP
MAX9588
AV = 2V/V OUTA
300mV
LPF
INB
CLAMP
LPF
AV = 2V/V
OUTB
INC
BIAS
LPF
AV = 2V/V
OUTC
Block Diagrams continued at end of data sheet.
________________________________________________________________ Maxim Integrated Products
1
For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642, or visit Maxim's website at www.maxim-ic.com.
Single, Dual, Triple, and Quad Standard-Definition Video Filter Amplifiers with AC-Coupled Input Buffers MAX9586-MAX9589
ABSOLUTE MAXIMUM RATINGS
VDD to GND ..............................................................-0.3V to +4V IN_ to GND ...............................................................-0.3V to +4V SHDN to GND...........................................................-0.3V to +4V OUT_ Short Circuit Duration to VDD, GND .................Continuous Continuous Input Current IN_, SHDN ....................................................................20mA Continuous Power Dissipation (TA = +70C) 5-Pin Thin SOT23 (derate 9.1mW/C above +70C) ....727mW 6-Pin Thin SOT23 (derate 9.1mW/C above +70C) ....727mW 8-Pin MAX (derate 4.5mW/C above +70C) .............362mW 10-Pin MAX (derate 5.6mW/C above +70C) ...........444mW Operating Temperature Range .........................-40C to +125C Junction Temperature ......................................................+150C Storage Temperature Range .............................-65C to +150C Lead Temperature (soldering, 10s) .................................+300C
Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS
(VDD = 3.3V, GND = 0V, VRL = no load, TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25C.) (Note 1)
PARAMETER Supply Voltage Range Supply Current Sync-Tip Clamp Level SYMBOL VDD IDD VCLP Per channel Sync-tip clamp VDD = 2.7V, sync-tip clamp input Input Voltage Range VIN Guaranteed by DC VDD = 2.7V, bias input voltage gain VDD = 3V, sync-tip clamp input VDD = 3V, bias input Sync Crush Input Clamping Current Maximum Input Source Resistance Bias Voltage Input Resistance VBIAS Bias circuit Bias circuit VDD = 2.7V, VIN = VCLP to (VCLP + 1.05V) VDD = 3V, VIN = VCLP to (VCLP + 1.2V) VDD = 2.7V, VIN = VBIAS 0.525V VDD = 3V, VIN = VBIAS 0.600V DC Gain Matching Output Level Guaranteed by DC voltage gain Measured at VOUT, IN_ = 0.1F to GND, RL = 150 to GND Sync-tip clamp Bias circuit 1.95 1.95 1.95 1.95 -2 0.2 0.40 Sync-tip clamp, percentage reduction in sync pulse (0.3VP-P), guaranteed by input clamping current measurement, measured at input Sync-tip clamp 1 300 0.50 11 2.00 2.00 2.00 2.00 0 0.3 1.3 2.04 2.04 V/V 2.04 2.04 +2 0.4 V % 0.62 0.24 CONDITIONS Guaranteed by PSRR MIN 2.7 4.25 TYP MAX 3.6 8 0.41 1.05 1.05 1.2 1.2 2 2 % A V k VP-P UNITS V mA V
DC Voltage Gain (Note 2)
AV
RL = 150 to GND
2
_______________________________________________________________________________________
Single, Dual, Triple, and Quad Standard-Definition Video Filter Amplifiers with AC-Coupled Input Buffers
ELECTRICAL CHARACTERISTICS (continued)
(VDD = 3.3V, GND = 0V, VRL = no load, TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25C.) (Note 1)
PARAMETER SYMBOL CONDITIONS Measured at output, VDD = 2.7V, VIN = VCLP to (VCLP + 1.05V), RL = 150 to -0.2V Measured at output, VDD = 2.7V, VIN = VCLP to (VCLP + 1.05V), RL = 150 to VDD/2 Sync-tip clamp Measured at output, VDD = 3V, VIN = VCLP to (VCLP + 1.2V), RL = 150 to -0.2V Measured at output, VDD = 3V, VIN = VCLP to (VCLP + 1.2V), RL = 150 to VDD/2 Measured at output, VDD = 3.135V, VIN = VCLP to (VCLP + 1.05V), RL = 75 to -0.2V Output-Voltage Swing Measured at output, VDD = 2.7V, VIN = VBIAS 0.525V, RL = 150 to -0.2V Measured at output, VDD = 2.7V, VIN = VBIAS 0.500V, RL = 150 to VDD/2 Bias Circuit Measured at output, VDD = 3V, VIN = VBIAS 0.600V, RL = 150 to -0.2V Measured at output, VDD = 3V, VIN = VBIAS 0.500V, RL = 150 to VDD/2 Measured at output, VDD = 3.135V, VIN = VBIAS 0.525V, RL = 75 to -0.2V Output Short-Circuit Current Output Resistance ROUT Short to GND (sourcing) Short to VDD (sinking) VOUT = 1.5V, -10mA ILOAD +10mA 2.1 MIN TYP 2.1 MAX UNITS
MAX9586-MAX9589
2.1
2.4
2.4
2.1 VP-P
2.0
2.4
2.0
2.1 140 70 0.2
mA
_______________________________________________________________________________________
3
Single, Dual, Triple, and Quad Standard-Definition Video Filter Amplifiers with AC-Coupled Input Buffers MAX9586-MAX9589
ELECTRICAL CHARACTERISTICS (continued)
(VDD = 3.3V, GND = 0V, VRL = no load, TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25C.) (Note 1)
PARAMETER Power-Supply Rejection Ratio SYMBOL 2.7V VDD 3.6V f = 1MHz, 100mVP-P 1dB passband flatness Standard-Definition Reconstruction Filter VOUT_ = 2VP-P, reference frequency is 100kHz DG f = 5.5MHz f = 9.5MHz f = 27MHz CONDITIONS MIN 48 29 8.5 -0.15 -3 -55 0.1 % dB TYP MAX UNITS dB MHz
Differential Gain
5-step modulated staircase of 129mV step size and 286mV peak-to-peak subcarrier amplitude, f = 4.43MHz 5-step modulated staircase of 129mV step size and 286mV peak-to-peak subcarrier amplitude, f = 4.43MHz 2T = 200ns, bar time is 18s; the beginning 2.5% and the ending 2.5% of the bar time are ignored 2T = 200ns 2T = 200ns, bar time is 18s; the beginning 2.5% and the ending 2.5% of the bar time are ignored 5-step staircase 100kHz f 5.5MHz, outputs are 2VP-P 100kHz f 5.5MHz f = 5.5MHz f = 4.43MHz
Differential Phase
DP
0.4
Degrees
2T Pulse-to-Bar K Rating 2T Pulse Response 2T Bar Response Nonlinearity Group Delay Distortion Peak Signal to RMS Noise Output Impedance All-Hostile Crosstalk
0.6 0.2 0.2 0 9 71 4.8 -64
K% K% K% % ns dB dB
Note 1: All devices are 100% production tested at TA = +25C. Specifications over temperature limits are guaranteed by design. Note 2: Voltage gain (AV) is a two-point measurement in which the output-voltage swing is divided by the input-voltage swing.
4
_______________________________________________________________________________________
Single, Dual, Triple, and Quad Standard-Definition Video Filter Amplifiers with AC-Coupled Input Buffers
Typical Operating Characteristics
(VDD = SHDN = +3.3V, video outputs have RL = 150 connected to GND, TA = +25C, unless otherwise noted.)
MAX9586-MAX9589
SMALL-SIGNAL GAIN vs. FREQUENCY
VOUT = 100mVP-P
MAX9586 toc01
SMALL-SIGNAL GAIN FLATNESS vs. FREQUENCY
MAX9856 toc02
LARGE-SIGNAL GAIN vs. FREQUENCY
VOUT = 2VP-P 0 -10 GAIN (dB) -20 -30 -40 -50 -60 -70
MAX9586 toc03
10 0 -10 GAIN (dB)
2 1 0 -1 GAIN (dB) VOUT = 100mVP-P
10
-20 -30 -40 -50 -60 -70 100k 1M 10M 100M FREQUENCY (Hz)
-2 -3 -4 -5 -6 -7 -8 1M 10M FREQUENCY (Hz) 100M
100k
1M
10M
100M
FREQUENCY (Hz)
LARGE-SIGNAL GAIN FLATNESS vs. FREQUENCY
MAX9856 toc04
GROUP DELAY vs. FREQUENCY
MAX9586 toc05
POWER-SUPPLY REJECTION RATIO vs. FREQUENCY
-10 -20
MAX9586 toc06
2 1 0 -1 GAIN (dB) -2 -3 -4 -5 -6 -7 -8 1M 10M FREQUENCY (Hz) VOUT = 2VP-P
120 100 80 DELAY (ns) 60 40 20 0
0
PSRR (dB) 100k 1M 10M 100M
-30 -40 -50 -60 -70 -80 10k 100k 1M FREQUENCY (Hz) 10M 100M
100M
FREQUENCY (Hz)
QUIESCENT SUPPLY CURRENT vs. TEMPERATURE
MAX9586 toc07
VOLTAGE GAIN vs. TEMPERATURE
MAX9586 toc08
DIFFERENTIAL GAIN AND PHASE
DIFFERENTIAL PHASE (deg) DIFFERENTIAL GAIN (%) 0 -0.1 -0.2 -0.3 -0.4 0.8 0.6 0.4 0.2 0 -0.2 -0.4 1 2 3 4 5 6 f = 4.43MHz 7 f = 4.43MHz
MAX9586 toc09
7.0 QUIESCENT SUPPLY CURRENT (mA) 6.5 6.0 5.5 5.0 4.5 4.0 3.5 3.0 2.5 2.0 -50 -25 0 25 50 75 100
2.04 2.03 2.02 VOLTAGE GAIN (V/V) 2.01 2.00 1.99 1.98 1.97 1.96 1.95
0.1
125
-50
-25
0
25
50
75
100
125
1
2
3
4
5
6
7
TEMPERATURE (C)
TEMPERATURE (C)
_______________________________________________________________________________________
5
Single, Dual, Triple, and Quad Standard-Definition Video Filter Amplifiers with AC-Coupled Input Buffers MAX9586-MAX9589
Typical Operating Characteristics (continued)
(VDD = SHDN = +3.3V, video outputs have RL = 150 connected to GND, TA = +25C, unless otherwise noted.)
2T RESPONSE
MAX9586 toc10
12.5T RESPONSE
MAX9586 toc11
NTC-7 VIDEO TEST SIGNAL
MAX9586 toc12
IN_ 200mV/div
IN_ 200mV/div
IN_ 500mV/div
OUT_ 400mV/div
OUT_ 400mV/div
OUT_ 1V/div
100ns/div
400ns/div
10s/div
PAL MULTIBURST RESPONSE
MAX9586 toc13
PAL COLOR BARS
MAX9586 toc14
FIELD SQUARE-WAVE RESPONSE
MAX9586 toc15
IN_ 500mV/div
IN_ 500mV/div
IN_ 500mV/div
OUT_ 1V/div
OUT_ 1V/div
OUT_ 1V/div
10s/div
10s/div
2ms/div
INPUT-TO-INPUT CROSSTALK vs. FREQUENCY
MAX9586 toc16
OUTPUT-TO-OUTPUT CROSSTALK vs. FREQUENCY
MAX9586 toc17
OUTPUT IMPEDANCE vs. FREQUENCY
MAX9586 toc18
0 -20 -40 GAIN (dB)
0 -20 -40 GAIN (dB) -60 -80 -100 -120
100
OUTPUT IMPEDANCE () 100k 1M 10M 100M
10
-60 -80 -100 -120 100k 1M 10M 100M FREQUENCY (Hz)
1
0.1
0.01 100k 1M FREQUENCY (Hz) 10M FREQUENCY (Hz)
6
_______________________________________________________________________________________
Single, Dual, Triple, and Quad Standard-Definition Video Filter Amplifiers with AC-Coupled Input Buffers
Pin Description
PIN MAX9586 5 SOT23 1 2 3 -- -- -- -- 4 -- -- -- -- 5 MAX9587 6 SOT23 -- 2 -- 3 1 -- -- -- 4 6 -- -- 5 MAX9588 8 MAX -- 4 -- 1 2 3 -- -- 7 6 5 -- 8 MAX9589 10 MAX -- 5 -- 1 2 3 4 -- 9 8 7 6 10 SHDN GND IN INA INB INC IND OUT OUTA OUTB OUTC OUTD VDD Active-Low Shutdown Input. Connect to GND to shut down. Ground Video Input Video Input A Video Input B Video Input C Video Input D Video Output Video Output A Video Output B Video Output C Video Output D Positive Power Supply. Bypass to GND with a 0.1F capacitor. NAME FUNCTION
MAX9586-MAX9589
+3.3V VIDEO SWITCH CVBS
SHDN
VDD
MAX9586
0.1F
GND
3.3V 0.1F VIDEO DECODER 0.1F
IN
CLAMP
LPF
AV = 2V/V
OUT 75 75
VDD
MAX9587
LUMA VIDEO SWITCH 0.1F INA
GND
3.3V 0.1F
0.1F CLAMP LPF AV = 2V/V OUTA 75 75 VIDEO DECODER
0.1F CHROMA INB
0.1F BIAS LPF AV = 2V/V OUTB 75 75
Figure 1. Typical Application Circuits for the MAX9586/MAX9587 (Anti-Alias Filter)
_______________________________________________________________________________________
7
Single, Dual, Triple, and Quad Standard-Definition Video Filter Amplifiers with AC-Coupled Input Buffers MAX9586-MAX9589
VDD MPEG DECODER VDD
MAX9588
CVBS VDD 0.1F INA
GND 75
3.3V 0.1F
DAC
CLAMP
LPF
AV = 2V/V
OUTA
CVBS
DAC
LUMA VDD
0.1F
INB
CLAMP
LPF
AV = 2V/V
OUTB
75 Y
DAC
CHROMA
0.1F
INC
BIAS
LPF
AV = 2V/V
OUTC
75 C
VDD MPEG DECODER VDD
MAX9589
CVBS 0.1F INA
GND 75
3.3V 0.1F
DAC
CLAMP
LPF
AV = 2V/V
OUTA
CVBS1
0.1F VDD
INB
CLAMP
LPF
AV = 2V/V
OUTB
75 CVBS2
DAC
LUMA VDD
0.1F
INC
CLAMP
LPF
AV = 2V/V
OUTC
75 Y
DAC
CHROMA
0.1F
IND
BIAS
LPF
AV = 2V/V
OUTD
75 C
Figure 2. Typical Application Circuits for the MAX9588/MAX9589 (Reconstruction Filter)
8 _______________________________________________________________________________________
Single, Dual, Triple, and Quad Standard-Definition Video Filter Amplifiers with AC-Coupled Input Buffers
Detailed Description
The MAX9586-MAX9589 filter and amplify the video DAC output in applications such as set-top boxes and televisions. These devices consist of input clamps, input bias circuits, lowpass filters, and gain of 2V/V output amplifiers capable of driving a standard 150 video load to ground.
Outputs
The video output amplifiers can both source and sink load current, allowing output loads to be DC- or ACcoupled. The amplifier output stage needs approximately 300mV of headroom from either supply rail. The devices have an internal level-shift circuit that positions the sync tip at approximately 300mV at the output. If the supply voltage is greater than 3.135V (5% below a 3.3V supply), each amplifier can drive two DC-coupled video loads to ground. If the supply is less than 3.135V, each amplifier can drive only one DC-coupled or AC-coupled video load.
MAX9586-MAX9589
Inputs
The input stages of the MAX9586-MAX9589 are either sync-tip clamps or bias circuits. Sync-tip clamps accept AC-coupled CVBS or luma video signals with sync pulses. The sync-tip voltage is internally set to 300mV. Bias circuit inputs accept AC-coupled chroma, a subcarrier modulated with the color information. The bias voltage of the bias circuits is approximately 500mV.
Shutdown (MAX9586)
The MAX9586 draws less than 1A supply current when SHDN is low. In shutdown mode, the amplifier output becomes high impedance.
Video Filter
The filter passband (1dB) is typically 8.5MHz, which makes the device suitable for standard-definition video signals from all sources (e.g., broadcast and DVD). Broadcast video signals are channel limited: NTSC signals have 4.2MHz bandwidth and PAL signals have 5MHz bandwidth. Video signals from a DVD player, however, are not channel limited, so the bandwidth of DVD video signals can approach the Nyquist limit of 6.75MHz. (Recommendation ITU-R BT.601-5 specifies 13.5MHz as the sampling rate for standard-definition video). Therefore, the maximum bandwidth of the signal is 6.75MHz. To ease the filtering requirements, most modern video systems oversample by two times, clocking the video current DAC at 27MHz.
Applications Information
AC-Coupling the Outputs
The outputs can be AC-coupled since the output stage can source and sink current as shown in Figure 3. Coupling capacitors should be 220F or greater to keep the highpass filter, formed by the 150 equivalent resistance of the video transmission line, to a corner frequency of 4.8Hz or below. The frame rate of PAL systems is 25Hz, and the frame rate of NTSC systems is 30Hz. The corner frequency should be well below the frame rate.
Power-Supply Bypassing and Ground
The MAX9586-MAX9589 operate from a single-supply voltage down to 2.7V, allowing for low-power operation. Bypass VDD to GND with a 0.1F capacitor. Place all external components as close as possible to the device.
_______________________________________________________________________________________
9
Single, Dual, Triple, and Quad Standard-Definition Video Filter Amplifiers with AC-Coupled Input Buffers MAX9586-MAX9589
VDD MPEG DECODER VDD
3.3V 0.1F
MAX9589
0.1F
GND
DAC
CVBS
INA
CLAMP
LPF
AV = 2V/V
OUTA
75
220F CVBS1
0.1F VDD
INB
CLAMP
LPF
AV = 2V/V
OUTB
75
220F CVBS2
DAC
LUMA VDD
0.1F
INC
CLAMP
LPF
AV = 2V/V
OUTC
75
220F Y
DAC
CHROMA
0.1F
IND
BIAS
LPF
AV = 2V/V
OUTD
75
220F C
Figure 3. AC-Coupled Outputs
10
______________________________________________________________________________________
Single, Dual, Triple, and Quad Standard-Definition Video Filter Amplifiers with AC-Coupled Input Buffers
Block Diagrams (continued)
MAX9586-MAX9589
SHDN UNKNOWN BIAS IN CLAMP
MAX9586
OUT
300mV AV = 2V/V
LPF
MAX9587
INA OUTA
CLAMP
LPF
AV = 2V/V
INB
BIAS
LPF
AV = 2V/V
OUTB
MAX9589
INA OUTA
CLAMP
LPF
AV = 2V/V
INB
CLAMP
LPF
AV = 2V/V
OUTB
INC
CLAMP
LPF
AV = 2V/V
OUTC
IND
BIAS
LPF
AV = 2V/V
OUTD
______________________________________________________________________________________
11
Single, Dual, Triple, and Quad Standard-Definition Video Filter Amplifiers with AC-Coupled Input Buffers MAX9586-MAX9589
Pin Configurations
TOP VIEW
SHDN 1
+ MAX9586
INA 5 VDD INB INC GND
1+ 2 3 4
8 7
VDD OUTA OUTB OUTC
MAX9588
6 5
GND 2
MAX
IN 3 4 OUT
SOT23
INB 1 +
6
OUTB
INA 1 INB 2 3 4 5
+
10 VDD 9 OUTA OUTB OUTC OUTD
GND 2
MAX9587
5
VDD
INC IND
MAX9589
8 7 6
INA 3
4
OUTA
GND
SOT23
MAX
Selector Guide
PART MAX9586AZK+T MAX9587AZT+T MAX9588AUA+T PIN-PACKAGE 5 SOT23-5 6 SOT23-6 8 MAX-8 PACKAGE SIZE 2.9mm x 1.6mm 2.9mm x 1.6mm 3mm x 3mm CHANNELS 1 2 3 4 TOP MARK ADSH AADI -- --
10 MAX-10 MAX9589AUB+T 3mm x 3mm Note: All devices are specified over the -40C to +125C operating temperature range. +Denotes a lead-free package.
Chip Information
PROCESS: BiCMOS
12
______________________________________________________________________________________
Single, Dual, Triple, and Quad Standard-Definition Video Filter Amplifiers with AC-Coupled Input Buffers
Package Information
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information, go to www.maxim-ic.com/packages.)
MAX9586-MAX9589
______________________________________________________________________________________
THIN SOT23.EPS
13
Single, Dual, Triple, and Quad Standard-Definition Video Filter Amplifiers with AC-Coupled Input Buffers MAX9586-MAX9589
Package Information (continued)
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information, go to www.maxim-ic.com/packages.)
14
______________________________________________________________________________________
Single, Dual, Triple, and Quad Standard-Definition Video Filter Amplifiers with AC-Coupled Input Buffers
Package Information (continued)
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information, go to www.maxim-ic.com/packages.) 6L THIN SOT23.EPS
MAX9586-MAX9589
______________________________________________________________________________________
15
Single, Dual, Triple, and Quad Standard-Definition Video Filter Amplifiers with AC-Coupled Input Buffers MAX9586-MAX9589
Package Information (continued)
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information, go to www.maxim-ic.com/packages.)
16
______________________________________________________________________________________
Single, Dual, Triple, and Quad Standard-Definition Video Filter Amplifiers with AC-Coupled Input Buffers
Package Information (continued)
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information, go to www.maxim-ic.com/packages.)
8LUMAXD.EPS
MAX9586-MAX9589
4X S
8
8
INCHES DIM A A1 A2 b MIN 0.002 0.030 MAX 0.043 0.006 0.037
MILLIMETERS MAX MIN 0.05 0.75 1.10 0.15 0.95
O0.500.1
E
H
0.60.1
c D e E H L
1
1
0.60.1
S
D
BOTTOM VIEW
0.014 0.010 0.007 0.005 0.120 0.116 0.0256 BSC 0.120 0.116 0.198 0.188 0.026 0.016 6 0 0.0207 BSC
0.25 0.36 0.13 0.18 2.95 3.05 0.65 BSC 2.95 3.05 4.78 5.03 0.41 0.66 0 6 0.5250 BSC
TOP VIEW
A2
A1
A
c e b L
SIDE VIEW
FRONT VIEW
PROPRIETARY INFORMATION TITLE:
PACKAGE OUTLINE, 8L uMAX/uSOP
APPROVAL DOCUMENT CONTROL NO. REV.
21-0036
1 1
J
______________________________________________________________________________________
17
Single, Dual, Triple, and Quad Standard-Definition Video Filter Amplifiers with AC-Coupled Input Buffers MAX9586-MAX9589
Package Information (continued)
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information, go to www.maxim-ic.com/packages.)
10LUMAX.EPS
1 1
e
10
4X S
10
INCHES MAX DIM MIN 0.043 A 0.006 A1 0.002 A2 0.030 0.037 0.120 D1 0.116 0.118 D2 0.114 0.120 E1 0.116 0.118 E2 0.114 0.199 H 0.187 L 0.0157 0.0275 L1 0.037 REF 0.0106 b 0.007 e 0.0197 BSC c 0.0035 0.0078 0.0196 REF S 0 6
MILLIMETERS MAX MIN 1.10 0.15 0.05 0.75 0.95 3.05 2.95 3.00 2.89 2.95 3.05 2.89 3.00 4.75 5.05 0.40 0.70 0.940 REF 0.177 0.270 0.500 BSC 0.090 0.200 0.498 REF 0 6
H
O0.500.1
0.60.1
1
1
0.60.1
TOP VIEW
BOTTOM VIEW
D2 GAGE PLANE A2 A b A1 D1
E2
c
E1 L1
L
FRONT VIEW
SIDE VIEW
PROPRIETARY INFORMATION TITLE:
PACKAGE OUTLINE, 10L uMAX/uSOP
APPROVAL DOCUMENT CONTROL NO. REV.
21-0061
Revision History
Pages changed at Rev 1: 1, 3, 24 Pages changed at Rev 2: 1-4, 13, 25 Pages changed at Rev 3: 1, 2, 7, 12-18 (deleted some package outlines) Pages changed at Rev 4: 1, 4, 5, 9, 18 Pages changed at Rev 5: 1, 18
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
18 ____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 (c) 2007 Maxim Integrated Products is a registered trademark of Maxim Integrated Products, Inc.
Heaney

▲Up To Search▲

Price & Availability of MAX95860710

	To Download MAX95860710 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .